一、入水：gate
進入位： gate location
水口形式：gate type
大水口：edge gate
細水口： pin-point gate
水口大小：gate size
轉水口： switching runner/gate

唧嘴口徑： sprue diameter

二、流道: runner
熱流道： hot runner,hot manifold
熱嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圓形流道：round(full/half runner
流道電腦分析：mold flow analysis
流道平衡:runner balance
熱嘴： hot sprue
熱流道板：hot manifold
發熱管：cartridge heater
探針: thermocouples
插頭： connector plug
插座： connector socket
密封/封料： seal

三、運水：water line
喉塞：line lpug
喉管：tube
塑膠管：plastic tube
快速接頭：jiffy quick connector plug/socker

四、模具零件： mold components
三板模：3-plate mold
二板模：2-plate mold
邊釘/導邊：leader pin/guide pin
邊司/導套：bushing/guide bushing
中托司：shoulder guide bushing
中托邊L：guide pin

頂針板：ejector retainner plate
托板： support plate
螺絲： screw
管釘：dowel pin
開模槽：ply bar scot
內模管位：core/cavity inter-lock
頂針： ejector pin
司筒：ejector sleeve
司筒針：ejector pin
推板：stripper plate
縮呵：movable core,return core core puller
扣機（尼龍拉勾）：nylon latch lock
斜頂：lifter
模胚（架）： mold base
上內模：cavity insert
下內模：core insert
行位（滑塊）： slide
鑲件：insert
壓座/斜雞：wedge
耐磨板/油板：wedge wear plate
壓條：plate  
撐頭: support pillar
唧嘴： sprue bushing
擋板：stop plate
定位圈：locating ring
鎖扣：latch
扣雞：parting lock set
推桿：push bar
栓打螺絲：S.H.S.B
頂板：eracuretun
活動臂：lever arm
分流錐：spure sperader
水口司:bush
垃圾釘：stop pin
隔片：buffle
彈弓柱：spring rod
彈弓:die spring
中托司：ejector guide bush

中托邊：ejector guide pin
鑲針：pin
銷子：dowel pin
波子彈弓：ball catch
喉塞: pipe plug
鎖模塊：lock plate
斜頂：angle from pin
斜頂桿：angle ejector rod
尼龍拉勾：parting locks
活動臂：lever arm
復位鍵、提前回桿：early return bar
氣閥：valves
斜導邊：angle pin
術語：terms
承壓平面平衡：parting surface support balance
模排氣：parting line venting
回針碰料位：return pin and cavity interference
模總高超出啤機規格：mold base shut hight
頂針碰運水：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用鑲件： Do not use (core/cavity) insert
用鈹銅做鑲件： use beryllium copper insert
初步（正式）模圖設計：preliinary (final) mold design
反呵：reverse core
彈弓壓縮量：spring compressed length
穩定性好：good stability,stable
強度不夠：insufficient rigidity
均勻冷卻：even cooling
扣模：sticking
熱膨脹：thero expansion
公差：tolorance
銅公(電極）：copper electrode